Pallet Deck Chair

 
DIY - Demonstrated by Mark Visser
Chill out with this rustic pallet deck chair

Build your own deck chair made from a pallet - the perfect rustic addition to any outdoor living area

Submit your own rating
Submit your own rating
Submit your own rating
Submit your own rating
Submit your own rating
0 Ratings
Thank you very much for your rating This function can be used only with cookies activated.
0 Ratings
  • Downloads for the project
  • Introduction

    Difficulty level

    Costs

    Time required

    Modernise your outdoor living area with this rustic pallet chair - a simple yet effective addition to any patio or alfresco area. Relax and enjoy summer in this trendy chair.

    • Easy
      Easy tools
      When you want simplicity.
    • Universal
      Universal tools
      Versatility for more.
    • Advanced
      Advanced tools
      When you seek the best.

    Required power tools:

    Other accessories:

    Required materials:

    • Large hardwood pallet
    • Baton screws
    • Packet of galvanized timber screws

    Show detailed material list

    Item

    pcs

    Designation

    Length

    Width

    Thickness

    Material

    0

    2

    Large hardwood pallet

    1

    12

    Baton screws

    100mm

    2

    1

    Packet of galvanized timber screws

    50mm

    1

    Break down the pallet

    Step 1
    Step 1

    Remove any nails or fereign materials that may be of danger to you or your equipment.

    2

    Prepare your materials

    Step 2
    Step 2

    Using the larger, solid pieces of pallet wood, you will need to cut the following -

    - 2 x pieces 605mm long with 77.5 degree parallel cut at each end (front and rear leg)

    - 2 x pieces 620mm long with 70.5 degree parallel cuts at each end (rear legs)

    - 2 pieces 505mm long with one end cut at 90 degree and opposite end cut on the acute 76 degree

    - 2 x pieces 860mm long with both ends cut at 90 degrees (seat rails) choose one end to be the top and cut a 60mm mitre at the top at 45 degrees

    - 9 x pieces of slat type material to cut at lengths of 650mm (seat boards)

    3

    Plane your edges

    Step 3
    Step 3

    Plane, sand and pencil edge all edges of the chair.

    4

    Clamp seat rail into position

    Step 4
    Step 4

    Pre-drill teo holes with two galvanized baton screws at each end. Remove the clamps and raise place two slats under the assembly you just made. Now, take an armrest piece and place it on its edge so that 2cm overhangs the outside edge of the rear leg. This should leave 50mm overhang at the front leg. Pre-drill holes and screw in position.

    5

    Armrest and backrest

    Step 5
    Step 5

    Place your backrest piece into position, at 700mm down from the top, make and line it up with the top of the seat rail. On the inside edge of the armrest piece, you need to notch out a 30mm piece at a depth of 20mm to accommodate the backrest.

    6

    Mirror the process

    Step 6
    Step 6

    Once you have notched the armrest, place the pieces in position, clamp, pre-drill and countersink.

    This completes one side of your chair, repeat the process to mirror the side you have made. Ensure you mirror the piece and don’t make it identical as it has to be opposite.

    Once both are finished, stand uprught and clamp a seat slat into a temporary place

    7

    Screw in the seat panels

    Step 7
    Step 7

    First, place your first seat slat on the seat rails and overhang by 2cm. Pre-drill and screw into place.

    8

    Backrest

    Step 8
    Step 8

    For the backrest, place your first piece 2.5cm aboce the edge. Pre-drill and screw into place.

    9

    Finishing touches

    Step 9
    Step 9

    Trim and mitre any sharp corners. Sand and pencil edge all of your pieces before assembly. Refer to images as tyour progress through the project.

     
    Pallet Deck Chair



    Legal note

    Bosch does not accept any responsibility for the instructions stored here. Bosch would also like to point out that you follow these instructions at your own risk. For your own safety, please take all the necessary precautions.


     

    Service Hotline

    For questions on our After Sales Service:

    :+61 1300 307 044

    Monday - Friday: 8:30 - 17:00


    To e-mail contact form

    Find a retailer

     
     
     
    AU
    Add to wish list
    Added to wish list
    Buy now
    Reset filter
    Show filter
    Hide filter
    Thank you very much for your rating
    Thank you very much for your rating
    Show other projects
    Hide other projects
    Hide article variants
    Show article variants
    Close application tip
    Open application tip
    Read experience report
    Close experience report
    Hide detailed material list
    Show detailed material list
    Comparison list
    Products
    Product
    Show more recommendations
    Hide further recommendations